{"product_id":"bielpord-2-5-ss304-adjustable-exhaust-elbow-45-stainless-steel-clamp-ready-105mm-length","title":"Bielpord 2.5\" SS304 Adjustable Exhaust Elbow — 45° Stainless Steel, Clamp-Ready 105mm Length","description":"\u003cp\u003e\u003cstrong\u003eBielpord's 2.5-inch SS304 adjustable exhaust elbow is a stainless-steel, clamp-ready bend designed to join and re-route custom or modified car exhaust systems.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThis adjustable stainless-steel elbow provides a compact, durable way to change exhaust direction on modified systems. Built from SS304, the pipe is manufactured with raised beads on each end to help clamps seat securely and to simplify cutting, splicing, or welding during installation. Confirm dimensions before purchase—small measurement variances may occur due to manual measuring.\u003c\/p\u003e\n\n\u003ch3\u003eHow does this elbow adapt to different exhaust layouts?\u003c\/h3\u003e\n\u003cp\u003eThe elbow is made to be adjusted and fitted into custom exhaust runs where a change of direction is needed. Its compact length and specific outer diameter let it work with many aftermarket systems when combined with clamps or welding. The raised humps at both ends stabilize clamps and reduce slippage after installation.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eOuter diameter: 63 mm (approximately 2.99 inches) for common 2.5\" systems\u003c\/li\u003e\n  \u003cli\u003eLength: 105 mm (about 4.3 inches) for tight-fit routing\u003c\/li\u003e\n  \u003cli\u003eWall thickness: 1.5 mm for corrosion resistance and structural stability\u003c\/li\u003e\n  \u003cli\u003eEnd humps designed to enhance clamp grip and alignment\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat materials and surface preparation are used for durability?\u003c\/h3\u003e\n\u003cp\u003eConstructed from SS304 stainless steel, the elbow resists heat and basic corrosion typical in exhaust environments. The pipe comes with a surface treatment intended to make cutting and welding straightforward for custom fabrication. This lets installers trim and join the elbow to other sections without excessive finishing work.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eMaterial: SS304 stainless steel for temperature and corrosion performance\u003c\/li\u003e\n  \u003cli\u003eSurface designed for easy cutting, splicing, and welding\u003c\/li\u003e\n  \u003cli\u003eRaised ends reduce the need for extra alignment hardware\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWill this part fit my car's exhaust system?\u003c\/h3\u003e\n\u003cp\u003eThe elbow is marketed as a universal adapter for modified exhaust systems, most commonly used with 2.5-inch (approx. 63 mm) tubing. It works well in many retrofit and custom applications but always check the pipe diameter and available routing space before ordering. Allow for the stated tolerance in manual measurements when planning your fitment.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDesigned for compatibility with many 2.5\" aftermarket exhaust pipes\u003c\/li\u003e\n  \u003cli\u003eCompact 105 mm length suits constrained installation areas\u003c\/li\u003e\n  \u003cli\u003eClamped or welded connections possible depending on installer preference\u003c\/li\u003e\n  \u003cli\u003eManual measurement tolerance: expect 1–5 mm variation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow do I install and secure the elbow for reliable performance?\u003c\/h3\u003e\n\u003cp\u003eInstallers can either clamp the elbow in place using the built-in raised humps or weld it into a permanent run after trimming to the required length. The humps help keep clamp pressure focused and prevent slippage, while the SS304 construction tolerates common exhaust heat cycles. For best results, trial-fit before final welds and use appropriate high-temperature clamps or exhaust welding techniques.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eTrial-fit and mark trimming points before cutting\u003c\/li\u003e\n  \u003cli\u003eUse high-temperature exhaust clamps on the raised humps for secure clamping\u003c\/li\u003e\n  \u003cli\u003eWeld joints for permanent installations with proper exhaust welding practice\u003c\/li\u003e\n  \u003cli\u003eVerify clearances around chassis and suspension after installation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: This Bielpord adjustable exhaust elbow suits do-it-yourselfers, custom exhaust fabricators, and performance shops working on modified or replacement exhaust systems that require a compact directional change. It is intended for users who need a durable SS304 connection piece for 2.5-inch (≈63 mm) tubing and who will check measurements and select their preferred clamping or welding method.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: What are the exact dimensions of this elbow?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Outer diameter 63 mm (≈2.99\"), length 105 mm (≈4.3\"), wall thickness 1.5 mm, with 1–5 mm measurement tolerance.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I clamp or weld this elbow?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes — the raised end humps are designed for secure clamping, and the SS304 surface is suited for cutting, splicing, or welding.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Bielpord","offers":[{"title":"Default Title","offer_id":48087011000478,"sku":"B0FLWLGMZ5","price":31.98,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/bielpord-front-angle-elbow.jpg?v=1785913479","url":"https:\/\/northtrailauto.ca\/products\/bielpord-2-5-ss304-adjustable-exhaust-elbow-45-stainless-steel-clamp-ready-105mm-length","provider":"North Trail Auto","version":"1.0","type":"link"}