{"product_id":"cnclol-bike-frame-protection-tape-3m-x-4-carbon-fiber-pattern-0-5mm-thick-scratch-chip-guard","title":"CNCLOL Bike Frame Protection Tape — 3m x 4\" Carbon-Fiber Pattern, 0.5mm Thick Scratch \u0026 Chip Guard","description":"\u003cp\u003e\u003cstrong\u003eCNCLOL bike frame protection tape is a 0.5mm thick carbon-fiber-pattern PVC\/PMMA film, sized 3m x 4\" (118\" x 10cm), designed to shield frames from chips, scratches, dirt and oils while remaining removable without sticky residue.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThis protective wrap combines a tough PVC\/PMMA face with a pressure-sensitive adhesive engineered to stick to curved tubes yet peel off cleanly. The carbon-fiber pattern adds a subtle textured gloss finish that blends with modern frames while providing impact resistance in high-wear zones. Long enough for multiple patches or a full-wrap application, the 3m length fits mountain, gravel, road and commuter bikes built from carbon, aluminum or steel.\u003c\/p\u003e\n\n\u003ch3\u003eHow will this film protect my bike during off-road rides?\u003c\/h3\u003e\n\n\u003cp\u003eThe CNCLOL protection tape absorbs small rock hits, fender rub and chain slap, preventing paint chips and abrasions that build up over time. Its slightly rigid 0.5mm thickness delivers a physical barrier while the patterned surface helps hide scuffs.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003e0.5mm PVC\/PMMA layer resists punctures and abrasion\u003c\/li\u003e\n  \u003cli\u003eCarbon-fiber pattern conceals marks and preserves appearance\u003c\/li\u003e\n  \u003cli\u003ePressure-sensitive adhesive stays put on rough terrain\u003c\/li\u003e\n  \u003cli\u003eResistant to oils, dirt and moisture for longer protection\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWill the tape conform to curved tubes and complex frame shapes?\u003c\/h3\u003e\n\n\u003cp\u003eThe adhesive is formulated with low initial tack and high holding power so the film can be eased into curves without bubbling. With careful application and smoothing pressure, it conforms to most tube profiles while keeping a flush finish.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eLow initial viscosity helps position the film accurately\u003c\/li\u003e\n  \u003cli\u003eHigh final adhesion prevents lifting at edges and joints\u003c\/li\u003e\n  \u003cli\u003eSemi-rigid film reduces wrinkling on moderate curves\u003c\/li\u003e\n  \u003cli\u003eCut-to-fit length and width allow tailored coverage\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow easy is installation and removal if I want to change graphics?\u003c\/h3\u003e\n\n\u003cp\u003eInstallation is straightforward: clean the area, align the strip, then press it down smoothing outward to avoid air pockets. When removal is desired the adhesive peels away cleanly without leaving a messy residue, provided the film hasn’t been exposed to extreme heat for prolonged periods.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eWipe frame with isopropyl alcohol before application\u003c\/li\u003e\n  \u003cli\u003eApply steady hand pressure to ensure even bonding\u003c\/li\u003e\n  \u003cli\u003eHeat gently for tight bends, then press to set\u003c\/li\u003e\n  \u003cli\u003eRemoves without sticky residue under normal conditions\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow much coverage does a 3m roll provide and where should I use it?\u003c\/h3\u003e\n\n\u003cp\u003eThe 3m (118\") length and 10cm (4\") width give ample material for targeted protection: chainstays, downtubes, headtube contact zones, and fork blades. You can create multiple patches or trim for near-full-wrap protection on smaller frames or use it strategically on high-impact spots.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003e3m length allows multiple patch placements or longer continuous strips\u003c\/li\u003e\n  \u003cli\u003e10cm width suits common high-wear areas like chainstays and downtubes\u003c\/li\u003e\n  \u003cli\u003eTrim with scissors or a craft knife for custom shapes\u003c\/li\u003e\n  \u003cli\u003eCompatible with carbon, aluminum and steel frames\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: Cyclists who want to preserve their frame’s finish without altering its look or committing to permanent paint changes. Ideal for mountain bikers, gravel riders, road cyclists and commuters who need abrasion resistance, a clean removable solution, and a carbon-fiber appearance for stealthy, protective styling.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Is this tape safe for carbon frames?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. The PVC\/PMMA film and pressure-sensitive adhesive are compatible with carbon, aluminum and steel when applied to a clean, cool surface.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I remove the film without damaging paint?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. The adhesive peels off cleanly under normal conditions and won’t leave residue if removed carefully; use gentle heat for stubborn edges.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"CNCLOL","offers":[{"title":"Default Title","offer_id":48083053805726,"sku":"B0DQD54JWX","price":52.98,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/cnclol-front-packaging-carbon-wrap.jpg?v=1785823169","url":"https:\/\/northtrailauto.ca\/products\/cnclol-bike-frame-protection-tape-3m-x-4-carbon-fiber-pattern-0-5mm-thick-scratch-chip-guard","provider":"North Trail Auto","version":"1.0","type":"link"}