{"product_id":"evil-energy-1-75-exhaust-clamp-2-pack-1-75in-butt-joint-stainless-steel-3in-strap","title":"EVIL ENERGY 1.75\" Exhaust Clamp 2-Pack — 1.75in Butt-Joint Stainless Steel, 3in Strap","description":"\u003cp\u003e\u003cstrong\u003eEVIL ENERGY 1.75\" exhaust clamp is a two-piece stainless steel butt-joint band clamp designed to join 1.75-inch outer-diameter exhaust pipes, mufflers or catalytic converter outlets without welding.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThis clamp kit contains two 1.75\" butt joint band clamps built from 304 stainless steel with a zinc-plated M10 bolt and nut, steel gasket and aluminum alloy I-block. The design spreads compressive force 360 degrees around the joint to form a mechanical seal and resist deformation. With a 3-inch (76.7 mm) strap width and 81 N·m recommended torque, these clamps offer a removable, no-weld alternative for exhaust connections and repairs.\u003c\/p\u003e\n\n\u003ch3\u003eHow does this clamp join 1.75\" exhaust pipes without welding?\u003c\/h3\u003e\n\u003cp\u003eThe band sleeve wraps around the abutted pipe ends and tightens via the M10 bolt and I-block, compressing the steel gasket to form a seal. Because the strap is wide and continuous, pressure is distributed evenly rather than concentrated at one point.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eFits 1.75-inch OD to 1.75-inch OD butt joints\u003c\/li\u003e\n  \u003cli\u003e3-inch strap width for broader contact area\u003c\/li\u003e\n  \u003cli\u003eSteel gasket and I-block for consistent compression\u003c\/li\u003e\n  \u003cli\u003eZinc-plated M10 bolt for secure clamping\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWill this clamp resist corrosion and hold up under exhaust conditions?\u003c\/h3\u003e\n\u003cp\u003eThe main band is made of 304 stainless steel, chosen for its corrosion resistance in typical exhaust environments. Fasteners are zinc-plated to provide sacrificial protection; however, regular inspections are recommended in harsh or salted-road conditions.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e304 stainless steel band for rust resistance\u003c\/li\u003e\n  \u003cli\u003eZinc-plated bolt and nut to reduce surface corrosion\u003c\/li\u003e\n  \u003cli\u003eAluminum alloy I-block resists galling during installation\u003c\/li\u003e\n  \u003cli\u003eSteel gasket provides a durable sealing surface\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow do I install and tighten this butt joint band clamp correctly?\u003c\/h3\u003e\n\u003cp\u003ePosition the band over the butt joint so the gasket aligns with the pipe seam, then hand-start the nut and tighten the M10 bolt incrementally. Torque to the specified 81 N·m in small steps to ensure even compression and avoid over-tightening which could deform the pipes.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eAlign pipe ends and slide the band over the joint\u003c\/li\u003e\n  \u003cli\u003eHand-thread the M10 nut, then tighten gradually with a torque wrench\u003c\/li\u003e\n  \u003cli\u003eTighten to around 81 N·m in several passes for even compression\u003c\/li\u003e\n  \u003cli\u003eInspect the seal and retorque after initial heat cycles if needed\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat applications and limitations should I expect from this clamp?\u003c\/h3\u003e\n\u003cp\u003eThis clamp is intended for mechanical joining of exhaust components such as resonators, mufflers, pipes and catalytic converter outlets where a 1.75\" OD butt joint exists. It’s not a substitute for a structural repair in severely damaged or misaligned systems and should not be used on pipes with larger diameters than specified.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eIdeal for exhaust pipes, mufflers, and catalytic converter connections\u003c\/li\u003e\n  \u003cli\u003eDesigned only for 1.75\" OD to 1.75\" OD butt joints\u003c\/li\u003e\n  \u003cli\u003eNo welding required, making installation and removal faster\u003c\/li\u003e\n  \u003cli\u003eNot intended to replace severely corroded or crushed pipe sections\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for? The EVIL ENERGY 1.75\" exhaust clamp is suited to DIY mechanics, professional exhaust shops and vehicle owners who want a removable, no-weld solution for joining 1.75-inch exhaust pipes and components. It’s especially useful for quick repairs, prototype exhaust builds, or when you need a secure mechanical seal without cutting and welding. For heavily damaged sections or custom fabrications beyond the clamp’s size range, consult a qualified technician.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can this clamp join 1.75\" to 1.5\" pipes?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. This clamp is sized for 1.75\" OD to 1.75\" OD butt joints only; mismatched diameters will not seal correctly.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Do I need special tools to install the clamp?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Basic hand tools and a torque wrench are recommended to tighten the M10 bolt to the specified 81 N·m for an even seal.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"EVIL ENERGY","offers":[{"title":"Default Title","offer_id":48086970990750,"sku":"B0D171P1JC","price":31.98,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/evil-energy-front-packaging-clamp_bb39dcb1-60a3-45c7-92c7-fa408b0dd6af.jpg?v=1785911294","url":"https:\/\/northtrailauto.ca\/products\/evil-energy-1-75-exhaust-clamp-2-pack-1-75in-butt-joint-stainless-steel-3in-strap","provider":"North Trail Auto","version":"1.0","type":"link"}