{"product_id":"ewk-pneumatic-car-dent-puller-kit-air-suction-slide-hammer-with-75-100-125mm-cups-for-paint-preserving-dent-removal","title":"EWK Pneumatic Car Dent Puller Kit — Air Suction Slide Hammer with 75\/100\/125mm Cups for Paint-Preserving Dent Removal","description":"\u003cp\u003e\u003cstrong\u003eEWK Pneumatic Car Dent Puller Kit is an air-powered suction and slide-hammer system designed to remove small-to-medium vehicle dents without glue or tabs.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThis kit pairs a compressed-air suction head with a shock-absorbing slide hammer and three rubber cups (75mm, 100mm, 125mm) so technicians and experienced DIYers can tackle door dings, shallow panel depressions, and other smooth-surface dents faster and with less cleanup. It’s built for use with a shop compressor at 90–150 PSI and focuses on paint-preserving dent extraction rather than full body restoration of heavily creased or torn panels.\u003c\/p\u003e\n\n\u003ch3\u003eHow does the pneumatic suction system work to pull dents?\u003c\/h3\u003e\n\u003cp\u003eThe tool connects to an air compressor and creates a strong vacuum at the cup face; the operator then applies controlled slide-hammer pulls to dislodge the dent. Because suction does much of the initial hold, the slide hammer provides added impulse without relying on adhesives or heat.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eConnects to standard shop compressors (recommended 90–150 PSI)\u003c\/li\u003e\n  \u003cli\u003eCreates instant vacuum — faster setup than glue tab methods\u003c\/li\u003e\n  \u003cli\u003eSlide hammer adds measured pulling force for stubborn dents\u003c\/li\u003e\n  \u003cli\u003eSoft rubber cups reduce direct paint abrasion during use\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich dents and panels is this kit best suited for?\u003c\/h3\u003e\n\u003cp\u003eThe EWK kit performs best on shallow-to-moderate depressions in smooth, uncreased metal panels: doors, fenders, trunk lids and quarter panels. It’s not a guaranteed fix for very sharp creases, large folds, or panels with existing paint failure, where welding, panel beating, or filler may be required.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eIdeal for door dings, mild parking lot dents, and hail damage spots\u003c\/li\u003e\n  \u003cli\u003eWorks on flat or gently curved areas rather than highly contoured trim\u003c\/li\u003e\n  \u003cli\u003eMultiple cup sizes allow targeting of small blemishes or wider depressions\u003c\/li\u003e\n  \u003cli\u003eRecommended for original paint surfaces where minimal disturbance is desired\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat setup and operating tips improve results and protect paint?\u003c\/h3\u003e\n\u003cp\u003eUse a clean surface and choose the cup size that covers the dent edge-to-edge for best suction. Start at lower compressor pressure to test hold, then increase to the recommended range if the cup slips; use steady, progressive hammer pulls rather than abrupt tugs to limit paint stress.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eClean panel area of dirt, wax, and moisture before seating the cup\u003c\/li\u003e\n  \u003cli\u003eBegin at lower PSI, then move toward 90–150 PSI as needed for hold\u003c\/li\u003e\n  \u003cli\u003eSelect 75mm for tight spots, 100mm for average dents, 125mm for larger areas\u003c\/li\u003e\n  \u003cli\u003eIf paint cracks or creases are present, stop and consult body repair methods\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: The EWK Pneumatic Dent Puller Kit is aimed at professional auto-body technicians, mobile repair specialists, and skilled DIY enthusiasts who want a quicker, glue-free way to remove many common dents while minimizing cleanup. It’s a practical addition for workshops that already use an air compressor and need a compact paint-friendly extraction tool; it should be used alongside other PDR tools for best results on complex or severe damage.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: What compressor pressure does the EWK dent puller need?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Use a compressor between 90–150 PSI (6.2–10.3 bar) for optimal suction and pulling performance.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Will this tool damage factory paint?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Soft rubber cups and controlled pulls minimize paint damage, but avoid use on cracked or heavily creased paint.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"EWK","offers":[{"title":"Default Title","offer_id":48082726715550,"sku":"B079FMW5T1","price":184.98,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/ewk-front-view-complete-kit_7d072a47-ab88-46bc-84f9-d978ce89a45f.jpg?v=1785812258","url":"https:\/\/northtrailauto.ca\/products\/ewk-pneumatic-car-dent-puller-kit-air-suction-slide-hammer-with-75-100-125mm-cups-for-paint-preserving-dent-removal","provider":"North Trail Auto","version":"1.0","type":"link"}