{"product_id":"frokom-30-series-go-kart-drive-belt-3-pack-27-1-32-for-5-7hp-karts-3-4-width-reinforced-low-noise","title":"Frokom 30 Series Go Kart Drive Belt — 3-Pack 27-1\/32\" for 5–7HP Karts, 3\/4\" Width, Reinforced Low-Noise","description":"\u003cp\u003e\u003cstrong\u003eThe Frokom 30 Series Go Kart Drive Belt is a durable replacement belt designed to restore reliable power transmission on 5–7HP karts (fits Manco 5959, Comet 203589, Ken-bar models).\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eWhen your go-kart starts slipping, squealing, or losing acceleration, the drive belt is often the culprit. Frokom engineered this 30 Series belt with quality rubber and polyester reinforcement to deliver consistent torque transfer, low noise, and long life. Supplied as a convenient three-pack, it’s intended for common kart platforms that use the Comet 30 Series TAV2 Bolt setup, so you can replace multiple machines or keep spares on hand.\u003c\/p\u003e\n\n\u003ch3\u003eHow does this belt improve my kart's performance?\u003c\/h3\u003e\n\u003cp\u003eThis belt is ground for precise side profiles and balanced to reduce slippage and vibration under load. That improved contact surface helps maintain steady power delivery from your engine to the driven pulley, which feels like smoother acceleration and less heat build-up during use.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eExquisitely ground sides for uniform pulley contact\u003c\/li\u003e\n  \u003cli\u003ePolyester thread reinforcement to resist stretch\u003c\/li\u003e\n  \u003cli\u003eCushioning properties that reduce noise and vibration\u003c\/li\u003e\n  \u003cli\u003eDesigned to handle typical 5–7HP load cycles\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat machines and measurements does this belt fit?\u003c\/h3\u003e\n\u003cp\u003eThe Frokom 30 Series is made to match many Manco, American Sportworks and Ken-bar karts that use Comet TAV2-style drive systems. Key dimensions make it suitable for setups where the belt length and pulley spacing meet the specified tolerances.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eWidth: 0.75 inches (3\/4\")\u003c\/li\u003e\n  \u003cli\u003eOutside length: 27-1\/32 inches\u003c\/li\u003e\n  \u003cli\u003eRecommended center distance: between 6-5\/8\" and 6-11\/16\"\u003c\/li\u003e\n  \u003cli\u003eCompatible examples: Manco 5959, Comet 203589, Kartco 7628\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow durable is the Frokom 30 Series belt in real-world conditions?\u003c\/h3\u003e\n\u003cp\u003eFrokom belts combine good-quality rubber with polyester cord to resist fatigue, stretching and some environmental stresses. They are tested under demanding conditions to ensure the belt keeps tension and resists delamination, giving longer service intervals compared with lower-quality alternatives.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eReinforced construction for limited elongation over time\u003c\/li\u003e\n  \u003cli\u003eAnti-static characteristics to reduce dust attraction and wear\u003c\/li\u003e\n  \u003cli\u003eLow-noise compound for quieter operation\u003c\/li\u003e\n  \u003cli\u003eThree-belt pack lets you rotate spares or replace multiple belts at once\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat should I check during installation and maintenance?\u003c\/h3\u003e\n\u003cp\u003eCorrect routing and proper pulley alignment are essential for belt life. Verify center-to-center pulley distance, inspect pulley faces for wear, and tension the belt to the manufacturer’s recommended specification to prevent premature failure.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eConfirm center distance is 6-5\/8\" to 6-11\/16\" before fitting\u003c\/li\u003e\n  \u003cli\u003eInspect pulleys for burrs, corrosion, or misalignment\u003c\/li\u003e\n  \u003cli\u003eReplace belts in matched sets when necessary for even load sharing\u003c\/li\u003e\n  \u003cli\u003eKeep spare belts from prolonged UV exposure to avoid drying\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: The Frokom 30 Series Go Kart Drive Belt three-pack is aimed at hobbyists, rental operators, and small shop owners who service Manco, American Sportworks, Kartco and Ken-bar karts with 5–7HP engines. It’s a practical choice if you need a ready-fit replacement for Comet 203589 \/ Manco 5959 style setups, want spares for fast maintenance, or prefer belts built for stable transmission and lower vibration without swapping pulleys or modifying drivetrains.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Does this belt fit my Manco 5959 kart?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes, it matches the dimensions and is listed compatible with Manco 5959 and equivalent Comet 203589 setups.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: What center distance is required for installation?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: The belt requires a pulley center distance between 6-5\/8 inches and 6-11\/16 inches.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Frokom","offers":[{"title":"Default Title","offer_id":48086886547614,"sku":"B0CT8V6KDR","price":33.48,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/frokom-front-packaging-3pack.jpg?v=1785909144","url":"https:\/\/northtrailauto.ca\/products\/frokom-30-series-go-kart-drive-belt-3-pack-27-1-32-for-5-7hp-karts-3-4-width-reinforced-low-noise","provider":"North Trail Auto","version":"1.0","type":"link"}