{"product_id":"pbymt-2-led-turn-signals-for-harley-1986-2024-smoked-lens-pack-81-led-front-rear","title":"PBYMT 2\" LED Turn Signals for Harley 1986-2024, Smoked Lens Pack, 81-LED Front \u0026 Rear","description":"\u003cp\u003e\u003cstrong\u003ePBYMT 2-inch LED turn signals are compact, ultra-bright replacements for compatible Harley-Davidson models that combine 81 SMD LEDs, smoked IP67 lens covers, and plug-and-play wiring for faster, clearer signaling.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eUpgrading to high-output LED signals improves visibility and refreshes your bike's look while staying compatible with the classic 2-inch bullet-style sockets found on many Harley-Davidson motorcycles from 1986 through 2024. This set provides front and rear units, four smoked covers for a stealthy finish, and an efficient circuit board designed for long life and stable operation. Installation is straightforward for most riders, though some bikes may need a load resistor to normalize flash rate.\u003c\/p\u003e\n\n\u003ch3\u003eWill these turn signals fit my Harley model?\u003c\/h3\u003e\n\u003cp\u003eThese lights are built specifically for 2-inch bullet-style housings used on Dyna, Softail, Sportster, Touring, Street Glide, Road King, and Road Glide models between 1986 and 2024. They are not compatible with 3-inch or 3-1\/4-inch flat-style turn signal housings.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDesigned for standard 2\" bullet-style sockets common on many Harley models.\u003c\/li\u003e\n  \u003cli\u003eCovers a broad model range: Dyna, Softail, Sportster, Touring families and variants.\u003c\/li\u003e\n  \u003cli\u003eNot suitable for larger 3\" or 3-1\/4\" flat-type signals—measure before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow much brighter and longer-lasting are these LEDs compared to stock bulbs?\u003c\/h3\u003e\n\u003cp\u003eEach unit packs 81 SMD LEDs and is engineered to deliver substantially higher lumen output than factory halogen bulbs or lower-count LED alternatives. The internal circuit and heat management are designed for endurance, giving an expected service life measured in tens of thousands of hours.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e81 high-intensity SMD LEDs for markedly improved visibility.\u003c\/li\u003e\n  \u003cli\u003eReportedly up to 600% brighter than typical halogen or small-LED setups.\u003c\/li\u003e\n  \u003cli\u003eDurable circuit board and thermal design for approximately 60,000+ hours of use.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eAre these waterproof and rugged enough for road use?\u003c\/h3\u003e\n\u003cp\u003eThe lens covers are made from PC material rated IP67, which keeps dust and water out under normal riding conditions. The smoked covers not only add a low-profile aesthetic but also maintain good light transmission so signals remain noticeable in daylight and wet weather.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eIP67-rated smoked PC lens covers provide dust and water resistance.\u003c\/li\u003e\n  \u003cli\u003eSturdy construction resists vibration and road exposure.\u003c\/li\u003e\n  \u003cli\u003eSmoked finish balances stealthy appearance with sufficient visibility.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow difficult is installation and will my bike need extra parts?\u003c\/h3\u003e\n\u003cp\u003eThese signals use an all-in-one plug-and-play wiring approach for quick swaps in many applications—some riders report completing installation in just minutes. Certain motorcycles with hyper-fast LED flash controllers or low-power bulb detection may require a load resistor to achieve a normal flash cadence.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003ePlug-and-play design for straightforward replacement of 2\" bullet-style signals.\u003c\/li\u003e\n  \u003cli\u003eTypical install time: a few minutes for each side when connectors match.\u003c\/li\u003e\n  \u003cli\u003eLoad resistor may be needed to correct hyper-fast flash on some models (not included).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: This set is aimed at Harley owners who want a compact, high-visibility LED upgrade that preserves classic bullet-signal mounting. Choose these if you have a compatible 2-inch housing, seek a brighter, longer-lasting signaling solution, and prefer a smoked, low-profile aesthetic. If your bike uses larger flat signals or you want integrated sequential effects, consider alternate products or verify fitment before purchase.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Do these fit all Harley models?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: They fit Harley models with 2\" bullet-style turn signal sockets from 1986–2024; not compatible with 3\" or 3-1\/4\" flat-style signals.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Will I need a resistor for proper flash rate?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Some bikes require a load resistor to correct fast LED flash speed; check your flasher behavior after install.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"PBYMT","offers":[{"title":"Default Title","offer_id":48085010383006,"sku":"B0F3234DCY","price":39.48,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/pbymt-front-signal-assembled.jpg?v=1785866667","url":"https:\/\/northtrailauto.ca\/products\/pbymt-2-led-turn-signals-for-harley-1986-2024-smoked-lens-pack-81-led-front-rear","provider":"North Trail Auto","version":"1.0","type":"link"}