{"product_id":"poli-glow-mitt-applicator-for-boats-rvs-damp-microfiber-streak-free-gelcoat-finish","title":"Poli Glow Mitt Applicator for Boats \u0026 RVs — Damp Microfiber, Streak-Free Gelcoat Finish","description":"\u003cstrong\u003eThe Poli Glow Mitt Applicator is a damp microfiber mitt designed to apply Poli Glow coatings evenly to fiberglass surfaces on boats and RVs, producing a smooth, streak-free finish.\u003c\/strong\u003e\n\n\u003cp\u003eIf you want a faster, more controlled way to spread Poli Glow on gelcoat and fiberglass than a small chamois or a bare hand, this microfiber mitt was built for the job. It replaces the older 7\" hand-held chamois applicator and gives broader, consistent coverage while keeping the product from puddling. The mitt is intended to be used slightly damp, wiped in straight passes, and rinsed periodically to maintain even application.\u003c\/p\u003e\n\n\u003ch3\u003eHow should I prepare the mitt before starting?\u003c\/h3\u003e\n\u003cp\u003eBegin by wetting the mitt with fresh water and wringing it until it’s damp but not dripping. Wrap and re-wring with a towel to remove excess moisture; this helps the mitt hold just enough product to spread Poli Glow evenly without streaks or runs. During longer jobs, rinse and repeat the process as needed.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDampen with fresh water, wring out until moist\u003c\/li\u003e\n  \u003cli\u003eWrap in towel and re-wring to remove excess water\u003c\/li\u003e\n  \u003cli\u003eWear disposable rubber or plastic gloves under the mitt\u003c\/li\u003e\n  \u003cli\u003eRinse mitt occasionally and re-dampen to maintain performance\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat is the recommended application technique for best results?\u003c\/h3\u003e\n\u003cp\u003ePour several lines of Poli Glow onto the palm area of the mitt and apply with straight, even wipes—either top-to-bottom or side-to-side—working a roughly 4' x 6' section at a time. Avoid circular motions; each thin coat dries quickly (typically 1–2 minutes depending on temperature), so plan to apply at least six thin coats before moving to the next area.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDrizzle product onto the mitt’s palm area for controlled dispensing\u003c\/li\u003e\n  \u003cli\u003eWipe in straight passes, not circles, across 4' x 6' sections\u003c\/li\u003e\n  \u003cli\u003eAllow approximately 1–2 minutes drying between thin coats\u003c\/li\u003e\n  \u003cli\u003eApply a minimum of six coats for a durable, even finish\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow do I maintain the mitt during and after use?\u003c\/h3\u003e\n\u003cp\u003eKeep the mitt damp while working by rinsing and re-wringing when buildup occurs; a clogged mitt will cause uneven coverage. After finishing, rinse thoroughly with fresh water, remove trapped product from the fibers, and allow to dry fully before storage to prolong its life and preserve performance.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRinse mitt during use to remove accumulated residue\u003c\/li\u003e\n  \u003cli\u003eRe-wring to restore the damp feel for consistent spreading\u003c\/li\u003e\n  \u003cli\u003eThoroughly wash and air dry after each job to avoid hardened buildup\u003c\/li\u003e\n  \u003cli\u003eStore dry in a cool place away from direct sunlight\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for? The Poli Glow Mitt Applicator is aimed at boat owners, marina professionals, and RV enthusiasts who want a faster, more uniform way to apply Poli Glow to fiberglass and gelcoat. It’s ideal for anyone replacing a small chamois applicator or seeking improved coverage across larger panels; it reduces finger contact with product and helps produce a smoother, more consistent finish when used as directed.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I use the mitt when it's dripping wet?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No, the mitt should be damp but not dripping; excess water dilutes Poli Glow and causes streaking.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: How many coats should I apply with the mitt?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Apply at least six thin coats, allowing about 1–2 minutes to dry between each coat.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Poli Glow","offers":[{"title":"Default Title","offer_id":48084422721694,"sku":"B00I82R3F2","price":30.48,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/poli-glow-mitt-front-view.jpg?v=1785854835","url":"https:\/\/northtrailauto.ca\/products\/poli-glow-mitt-applicator-for-boats-rvs-damp-microfiber-streak-free-gelcoat-finish","provider":"North Trail Auto","version":"1.0","type":"link"}