{"product_id":"ucreative-an10-nylon-braided-fuel-line-kit-10ft-cpe-hose-with-swivel-an-fittings-clamp-500-psi-rated","title":"Ucreative AN10 Nylon-Braided Fuel Line Kit 10ft CPE Hose with Swivel AN Fittings \u0026 Clamp — 500 PSI Rated","description":"\u003cp\u003e\u003cstrong\u003eUcreative's 10-foot AN10 CPE nylon-braided fuel line kit is a ready-to-install fuel delivery hose assembly with matching AN swivel fittings and a clamp, built for high-pressure automotive applications.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThis kit combines a 10-foot length of CPE synthetic rubber hose wrapped in nylon braid with a selection of swivel AN hose ends so you can route fuel lines cleanly and securely. Designed for use where PTFE or rubber hoses are not appropriate, the assembly provides a durable pathway rated for demanding environments, with temperature and pressure thresholds suitable for many performance and replacement uses. The package also includes a separator clamp to keep runs neat and prevent chafing.\u003c\/p\u003e\n\n\u003ch3\u003eWhat components come with the complete fuel line kit?\u003c\/h3\u003e\n\u003cp\u003eThe kit includes the hose plus multiple swivel fittings so you can configure straight and angled connections without cutting extras. Each fitting is designed to crimp onto the CPE\/nylon line for a sealed connection, and a clamp is included to anchor the hose along the chassis or frame.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e1 × 10-foot CPE nylon-braided hose (AN10 internal diameter)\u003c\/li\u003e\n  \u003cli\u003e2 × straight swivel AN hose ends for inline runs\u003c\/li\u003e\n  \u003cli\u003e2 × 45° swivel AN hose ends for moderate angle bends\u003c\/li\u003e\n  \u003cli\u003e2 × 90° swivel AN hose ends for tight corners and bulkhead exits\u003c\/li\u003e\n  \u003cli\u003e1 × hose separator clamp for routing and vibration isolation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow does this hose perform under pressure and temperature extremes?\u003c\/h3\u003e\n\u003cp\u003eThe CPE synthetic rubber core with a tough nylon braid gives the hose good mechanical strength and a broad operating range. It’s rated for a maximum working pressure of 500 psi and a bursting pressure around 2000 psi, while handling temperatures from deep cold up to high heat commonly seen in engine bays.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eMaximum working pressure: 500 psi for sustained operation\u003c\/li\u003e\n  \u003cli\u003eBurst pressure: approximately 2000 psi for safety margin\u003c\/li\u003e\n  \u003cli\u003eTemperature capability: from -40°F up to 257°F (-40°C to 125°C)\u003c\/li\u003e\n  \u003cli\u003eConstruction: CPE rubber core with nylon braid for abrasion resistance\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich fittings and hose types are and aren’t compatible?\u003c\/h3\u003e\n\u003cp\u003eThe supplied AN-style fittings are matched to the kit’s CPE nylon-braided hose and are not intended for use with every hose material. Avoid pairing these fittings with PTFE-lined, E85-specific rubber, or other incompatible hose types to prevent poor seals or leaks.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eCompatible: CPE synthetic rubber hose with nylon braid (included)\u003c\/li\u003e\n  \u003cli\u003eNot compatible: PTFE-lined hoses, E85-specific rubber hoses, or certain aftermarket rubber lines\u003c\/li\u003e\n  \u003cli\u003eRecommendation: use the included fittings only on the supplied hose for best seal integrity\u003c\/li\u003e\n  \u003cli\u003eInstaller note: professional installation is recommended to ensure correct crimping and leak-free joints\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow should I plan and install this 10 ft AN10 hose kit?\u003c\/h3\u003e\n\u003cp\u003eMeasure twice before cutting: confirm the 0.56-inch inner diameter and 10-foot length meet your route and connector needs. Use the right crimp tooling or have a shop install the swivel ends; improper assembly can cause leaks. The included separator clamp helps secure the hose away from hot surfaces and moving parts.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eHose ID: 0.56 inch (14.2 mm); OD: 0.78 inch (20 mm) — verify fitment with your fittings\u003c\/li\u003e\n  \u003cli\u003ePlan routing to minimize sharp bends and heat exposure; use included 45°\/90° fittings where needed\u003c\/li\u003e\n  \u003cli\u003eProfessional crimping or experienced installer recommended to ensure leak-free connections\u003c\/li\u003e\n  \u003cli\u003eFree replacement offered if a leak occurs (no return required) — follow seller instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this kit best suited for: Enthusiasts upgrading fuel lines on performance cars, custom fabricators routing new fuel systems, and repair shops replacing worn nylon-braided CPE lines will find this Ucreative kit convenient. It’s meant for users who need a robust, pre-matched hose and fitting set rated for high pressure and elevated temperatures, and who either have the tools to crimp AN fittings properly or will use a professional installer to complete the job.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Is this AN10 hose compatible with E85 fuel?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. The included CPE\/nylon hose and fittings are not compatible with E85 or PTFE-lined hoses.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: What is the inner diameter and length of the hose?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: The hose ID is 0.56 inches (14.2 mm) and the supplied length is 10 feet.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Ucreative","offers":[{"title":"Default Title","offer_id":48080932896926,"sku":"B0D566S9Q6","price":67.98,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/ucreative-front-packaging-an10-fuel-line-kit.jpg?v=1785792819","url":"https:\/\/northtrailauto.ca\/products\/ucreative-an10-nylon-braided-fuel-line-kit-10ft-cpe-hose-with-swivel-an-fittings-clamp-500-psi-rated","provider":"North Trail Auto","version":"1.0","type":"link"}