{"product_id":"vevor-wheel-alignment-tool-toe-plates-2-pack-stainless-steel-with-5m-tapes-conversion-chart","title":"VEVOR Wheel Alignment Tool Toe Plates - 2-Pack Stainless Steel with 5m Tapes \u0026 Conversion Chart","description":"\u003cstrong\u003eVEVOR's two-piece stainless steel toe plate kit measures wheel toe angles accurately and works on a wide range of cars, trucks, Jeeps, UTVs and ATVs.\u003c\/strong\u003e\n\u003cp\u003eThis wheel alignment tool kit is built to help DIY mechanics and professional technicians measure toe angle without removing suspension parts or relying on expensive alignment machines. The set includes two heavy-duty SUS201 toe plates, two 5 m tape measures calibrated in 1\/32\" increments, and a conversion chart plus manual so you can convert linear differences into toe angles quickly. Designed with multiple hub hole patterns and anti-fall slots for the tape head, the kit supports common bolt patterns and makes single-person measurements practical.\u003c\/p\u003e\n\n\u003ch3\u003eHow do I use these toe plates to measure toe angle?\u003c\/h3\u003e\n\u003cp\u003eMount each toe plate directly to the wheel hub after removing the tire to avoid sidewall or tread distortion. Run the tape measures to fixed reference points and use the included conversion chart to translate the tape differences into toe angle degrees.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRemove the tire and thread toe plate onto hub studs for a true hub-centered reference.\u003c\/li\u003e\n  \u003cli\u003eExtend both 5 m tapes to the chosen reference point on front and rear of rim or brake disc.\u003c\/li\u003e\n  \u003cli\u003eRecord linear differences and consult the conversion chart to get toe in degrees or inches.\u003c\/li\u003e\n  \u003cli\u003eRepeat on the opposite wheel and adjust tie rods until desired spec is reached.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat makes the stainless-steel plates better than aluminum alternatives?\u003c\/h3\u003e\n\u003cp\u003eThese toe plates are stamped from SUS201 stainless steel for greater rigidity and corrosion resistance compared with thin aluminum plates. The heavier construction reduces flex and keeps alignment readings consistent over repeated use.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eThicker stainless steel resists bending under torque when mounted to the hub.\u003c\/li\u003e\n  \u003cli\u003eStainless composition reduces risk of rust in shop or outdoor settings.\u003c\/li\u003e\n  \u003cli\u003eDurable slot edges hold tape heads firmly to prevent slippage during solo work.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich vehicles and hub patterns does this tool support?\u003c\/h3\u003e\n\u003cp\u003eThe toe plate design includes multiple bolt hole patterns to fit many passenger and off-road wheel hubs, making it suitable for Jeeps, trucks, UTVs and most ATVs. The kit lists compatible hub sizes and commonly used bolt patterns to simplify selection before purchase.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eSupports 5 x 4.5\", 5 x 5\", 5 x 5.5\" and 6 x 5.5\" bolt patterns.\u003c\/li\u003e\n  \u003cli\u003eIncludes fitment for 8 x 6.5\" and 8 x 170 mm wheels and UTV\/ATV 4\/156.\u003c\/li\u003e\n  \u003cli\u003eTwo plates allow left and right side measurement without swapping hardware.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCan I use this tool alone, and how accurate are the readings?\u003c\/h3\u003e\n\u003cp\u003eThe built-in anti-fall tape slots and clear tape graduations make single-person operation achievable while maintaining repeatable measurements. Accuracy depends on consistent reference points and careful use of the conversion chart; the supplied 1\/32\" tape graduations provide fine linear resolution for precise angle conversion.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eAnti-fall slots secure tape head so one person can measure both sides reliably.\u003c\/li\u003e\n  \u003cli\u003eTwo 5 m tape measures avoid having to swap or extend tapes beyond comfort range.\u003c\/li\u003e\n  \u003cli\u003eManual and conversion chart reduce calculation errors and speed up workflow.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this kit for: The VEVOR Wheel Alignment Tool Kit is aimed at car owners, off-road enthusiasts and small repair shops who need a cost-effective, portable way to measure and correct toe angles without a full alignment rack. If you work on Jeeps, trucks, UTVs or ATVs, need a durable tool that survives shop conditions, and prefer a guided measurement process with conversion references, this two-plate stainless-steel kit delivers repeatable alignment data you can act on.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Do I need to remove the tire to use these toe plates?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. Removing the tire and mounting the plate on the hub reduces sidewall errors and gives truer toe measurements.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Which bolt patterns are supported?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: The plates fit common patterns including 5×4.5, 5×5, 5×5.5, 6×5.5, 8×6.5, 8×170 mm and UTV\/ATV 4\/156.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"VEVOR","offers":[{"title":"Default Title","offer_id":48083291701406,"sku":"B0CPYBJXCS","price":61.85,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0781\/2041\/9486\/files\/vevor-toe-plates-front-view.jpg?v=1785830705","url":"https:\/\/northtrailauto.ca\/products\/vevor-wheel-alignment-tool-toe-plates-2-pack-stainless-steel-with-5m-tapes-conversion-chart","provider":"North Trail Auto","version":"1.0","type":"link"}