Tabazy CV Boot Clamp Tool Kit — 13pc Drive‑Shaft Banding Tool with 12 Stainless Steel Clamps (Small & Large) for Cars and ATVs

Tabazy CV Joint Banding Boot Axle Clamp Tool Kit is a 13-piece set that tightens, locks, and trims stainless-steel CV boot band clamps for most cars and ATVs with one adjustable drive‑shaft tool.

When replacing or repairing CV boots, a reliable clamp and a clean, secure installation matter. This Tabazy kit groups a hardened steel banding tool with a selection of six small and six large stainless‑steel ear-style clamps so you can tension, lock and cut excess strap quickly. The tool’s winding and built-in cutter make repeatable clamp tensioning straightforward, while the two clamp sizes cover a wide range of axle diameters.

How does the Tabazy tool tighten and cut CV boot bands?

The included banding tool uses a manual winding mechanism to draw the stainless strap tight through locking teeth; each rotation increases tension until the clamp seats. When you reach the desired tension, the tool’s integrated cutter trims the remaining strap for a neat finish. Its steel construction is designed to resist bending under load for reliable, repeatable use.

• Built-in winding drive tightens clamps progressively for uniform pressure.
• Locking teeth hold the strap firmly as tension increases.
• Integrated cutter trims excess banding cleanly without separate tools.
• One-piece steel tool resists deformation during heavy use.

What clamp sizes and fitments are included in the kit?

Tabazy supplies six small and six large ear-style stainless-steel clamps that accommodate common CV and axle boot diameters. The small clamps fit 45–80 mm diameters, while the large clamps extend up to 170 mm, making the set useful for many cars, light trucks and ATVs. Each clamp is stamped from 0.28 mm thick, 7 mm wide stainless steel for corrosion resistance and gripping strength.

• Small clamps: 45–80 mm (1.77–3.14 in) diameter range, 7 mm wide.
• Large clamps: 45–170 mm (1.77–6.69 in) diameter range, 7 mm wide.
• 12 total clamps cover a broad span of axle sizes.
• Stainless steel resists rust and holds mechanical tension.

How do I use the kit safely and get a professional result?

Begin by seating the boot and selecting the correct clamp size for the axle diameter. Thread the clamp through the tool, wind until snug and check boot alignment before final trimming. Wear safety glasses when cutting and inspect the clamp ear to ensure it’s fully seated and free of sharp burrs.

• Select clamp size to avoid over- or under-tightening the boot lip.
• Wind the band gradually, checking for even compression around the boot.
• Use the built-in cutter to remove excess strap, then smooth any sharp edges.
• Inspect clamps periodically for secure seating and corrosion.

What materials and durability features does the set offer?

The Tabazy tool is forged from hardened steel for torsional strength and long life, while the clamps are stamped stainless steel to withstand moisture and road debris. The clamp thickness and width are balanced to hold tension without cutting into rubber boots when installed correctly. Together they offer a maintenance‑grade solution for repeated shop or home use.

• Tool: high‑quality steel with integrated cutter and winding mechanism.
• Clamps: stainless steel, 0.28 mm thick and 7 mm wide for consistent hold.
• Design resists deformation and maintains tension under vibration.
• Suitable for repeated installations in garage or field environments.

Who is this for: The Tabazy CV Joint Banding Boot Axle Clamp Tool Kit is aimed at DIY mechanics, independent shops and fleet technicians who need a compact, reusable banding solution. If you service passenger cars, light trucks or ATVs and replace CV or axle boots regularly, this kit supplies the adjustable clamps and a single durable tool to speed installations while delivering secure, corrosion‑resistant clamps.